Special price US $59.50 MKS SBASE V1.3 mainboard + MKS TFT28 V4.0 touch display full color TFT FDM printer control parts al

MKS SBASE V1.3 mainboard + MKS TFT28 V4.0 touch display full color TFT FDM printer control parts al

[1000005744717] Name: Smoothieboard MKS SBASEV1.3Packing List1pcs *MKSSBASE V1.31pcs* MKS TFT28V4.01pcs *USB1pcs * Flat cableFeatures Support highly modular open source firmware Smoothieware. Easy to edit config.txt file.No complicate firmware editing necessary. Fully supports network functionality. Besides the regular USB connection an Ethernet network cable can be connected directly to a network for browser control. Board IP address can be configure in config.txt. Setcurrent directly on config ,protect driver or potentiometer from getting burned whenadjust the current. This circuit board with high-quality 4-layer and better heatsink. Using a dedicated power supply chip, stablyensure power output.(Please note that MKS SBASEcan't work with OLED12864 and LCD2004displMore features as following WiringSIZEPINOUTHow to use 1.Copy "firmware.bin" and "config" from config file to SD card(SDsmaller than 64Gb).Need to change config name . For example: Change into 2.Adjust config.txt according to the configuration . 3.Refer to MKS-SBASE PIN , make correction connection. Such as stepper motor ,endstops. 4.Plug the SD card to the board, after power on, it will automatic update . 5.If connect computer with USB, need to install the driver(Refer to below specification ). Install the Driver First, you should upload the zip file. Then, plug the USB to computer . Next, enter device manger . Thenwill turn up COM after installsuccessfully. Download Firmware and Update Copy configuration (including firmware.bin and config.txt) to SD card, insert to the board and power on, it will automatic update . After successful updated, the file name will turn intofirmware.cur.Name:MKS TFT28Touch ScreenMKS TFT28 is a colorful touch screen which is used independently on 3d printer.This display is no need to set mainboard firmware and work together directly.And it is easy to replace into your logo and edit your local language.Also, it is available to self-define some commands .More features as follows:WiringSizeHow to assemble with mainboard.Set the baud rate, ensure both TFT and controller board are the same.1. Ramps1.4Set the baud rate, both TFT and Ramps1.4 are the same.Connect to AUX-1 on Ramps1.4.Move the jumper to 12V.TFT needs to power by a external 12V electricity supply.2.MKSSeries mainboardsSuch as, MKS SBASE,MKS MINI,MKS GEN,MKS BASE, MKS GEN L,etc.Flash firmware to mainboard .(TFT display hasupdated latest config inside already).Connect TFT display to AUX-1 of the board.No need to configure on board firmware,they will work together directly after wire.The boardsneed a external 12V power supply.3.Firmware UpdatePlease copy following documents to the root of SD card.(Please don't edit the documents name.)mks_pic mks_config mkstft28Then, plug the SD card to the TFT and power on. It will update automatically.4.Config5.BedLevelingAuto LevelingAfter the machine assembles with a bed leveling controller, then run leveling on TFT interface.#The command of auto leveling (G29 is available for Marlin.While G32 is for Repetier and Smoothieware)>cfg_auto_leveling_cmd:G28;G29;Manual LevelingManual leveling is good for MB,i3 etc machines. It is available to set 3,4,5 point .#The point number of manual leveling:(3,4,5 point available)>cfg_point_number:46.Filament ReplaceIt is easy to replace the filament when it runs out.You are able to set temperature and the speed of filament in-out on config.As following:#the speed of filament replacing(mm/min)>cfg_filament_change_speed:1200#the length of filament replacing(mm)>cfg_filament_change_step:5#the min temperature of filament replacing>cfg_filament_limit_temperature:175Then, here is the steps toreplace filament.1).On printingpause-----more-----change----in/out-----stop2).Before startprintingset-----change-----preheat-----in/out-----stop7.Print from BreakpointTFT has a one of the excellent features is able to print from Breakpoint.Below is the way to do it.Firstly, set target temperature of extruder and heated bed, and then preheat.Secondly, when preheat ready, go home .(Notice: if power off happens during operating printing from breakpoint, please must home .)Thirdly, move extruder to the breakpoint which is available to set allowable error.#Breakpoints continued playing Z-axis error setting>cfg_breakpoint_z_error:0.2Fourth, click set, and then click Continue(Means Print from Breakpoint).After that, choose the file you want.(If you pause the printing, and turn the printer off,then it will resume to print from the pause point after power on.)8.Filament Outage DetectingConnect detecting switch to PB1 of TFT.Set configurationto triggerlow level or high level available.#the level signal of outage detection module PB1(low level:0; high level:1)>cfg_PB0_PB1_Level:19.Auto off after Print FinishesEnable this function on config,and take concerted with PWC switch.#whether set machine auto-off after print finishes(auto-off:1; NO:0)>cfg_print_finish_close_Machine:010. MKS WIFIMKS TFT supports WIFI remote control. Please set configurations.As follow:#wifi mode(AP:1; STA:2)>cfg_wifi_mode:1#wifi name and password>cfg_wifi_ap_name:MKS_wifi>cfg_wifi_key_code:makerbase#Dynamic access IP>cfg_ip_dhcp_flag:1#IP/mask/gateway>cfg_ip_address:192.168.3.100>cfg_ip_mask:255.255.255.0>cfg_ip_gate:192.168.3.111.WiFiWiring on TFT 12.User-Defined Function